cutting springs to lower car

Make it go fast! Kick it up a notch. Post tips in here.
Post Reply
warrenrhen
Posts: 28
Joined: Fri Nov 13, 2020 10:09 pm
Your car is a: 1979 fiat 124 spider
Location: Apache Junction AZ

cutting springs to lower car

Post by warrenrhen »

I've replaced my bumpers with Vics bumperettes. Now I want to lower the whole car slightly and get the back more level with the front. Nothing radical just a nie street car. I'm thinking one coil in the back and a 1/2 coil in the front. Anybody have experience with this? How much will that lower the back? and will Need shorter shocks?
Cheers Warren
Cheers, Warren
79 124 spider
18 Dodge Charger R/T
20 Vespa 300 GTS HPE
redcars
Patron 2020
Patron 2020
Posts: 487
Joined: Sat Jul 31, 2010 9:36 pm
Your car is a: 1981 Spider 2000
Location: Collinsville, IL

Re: cutting springs to lower car

Post by redcars »

You will not need different shocks. How much you need to take off will depend on your car and your tastes. I would go with a half coil at a time. The back springs are easy to take in and out. The fronts are more of a challenge. Be sure to get a spring commpessor.
1987 Lotus Super 7 clone
1981 Fiat Spider 2000 AT
1982 Fiat Spider 2000 5sd
1970 Fiat Coupe
User avatar
RRoller123
Patron 2020
Patron 2020
Posts: 8179
Joined: Sun Nov 13, 2011 2:04 pm
Your car is a: 1980 FI SPIDER 2000
Location: SAGAMORE BEACH, MA USA

Re: cutting springs to lower car

Post by RRoller123 »

Reading about this over the years, the general consensus seems to be to do this very little at a time, and not take too much. 1/2 turn is a good start, may be a good stopping point too.
'80 FI Spider 2000
'74 and '79 X1/9 (past)
'75 BMW R75/6
2011 Chevy Malibu (daily driver)
2010 Chevy Silverado 2500HD Ext Cab 4WD/STD BED
2002 Edgewater 175CC 80HP 4-Stroke Yamaha
2003 Jaguar XK8
2003 Jaguar XKR
2021 Jayco 22RB
2019 Bianchi Torino Bicycle
jon8christine
Patron 2018
Patron 2018
Posts: 130
Joined: Sat Mar 12, 2011 10:05 pm
Your car is a: 1976 Fiat 124 Spider
Location: Wyoming

Re: cutting springs to lower car

Post by jon8christine »

When I cut my rear springs to level out the car I took either 1 coil or maybe 1-1/2 off the rear w/ the bumpers removed. I did it in stages as others have mentioned. A few years later I redid all the suspension for autocross and bought Allisons lowering springs...just right.
TheBender
Patron 2019
Patron 2019
Posts: 220
Joined: Fri Aug 11, 2017 1:57 pm
Your car is a: 1978 124 Spider

Re: cutting springs to lower car

Post by TheBender »

I decided to get Allison’s lowering progressive springs and new shocks. Love both the height and also the improved ride quality.
profcucchi
Posts: 248
Joined: Sun Oct 23, 2011 2:12 pm
Your car is a: 1979 Fiat 2000
Location: Toronto, On

Re: cutting springs to lower car

Post by profcucchi »

I gave this a lot of thought, too.

A Fiat and Alfa mechanic told me once you cut springs, you throw off the geometry of the vehicle. and it makes for a stiffer ride.

I decided to hold out until I could get proper lowering springs.
1979 Fiat 2000 "Luigi"
redcars
Patron 2020
Patron 2020
Posts: 487
Joined: Sat Jul 31, 2010 9:36 pm
Your car is a: 1981 Spider 2000
Location: Collinsville, IL

Re: cutting springs to lower car

Post by redcars »

Lowering springs do the same thing, it just costs you more. I have did both. Now that I am old I have went to stock Springs and wheels for the nicer ride. When I want very good handling and a harsh ride I get out the Super 7 replica.
1987 Lotus Super 7 clone
1981 Fiat Spider 2000 AT
1982 Fiat Spider 2000 5sd
1970 Fiat Coupe
seawood
Posts: 19
Joined: Tue Mar 02, 2021 4:45 pm
Your car is a: 1980 124 spider

Re: cutting springs to lower car

Post by seawood »

"I gave this a lot of thought, too.

A Fiat and Alfa mechanic told me once you cut springs, you throw off the geometry of the vehicle. and it makes for a stiffer ride.

I decided to hold out until I could get proper lowering springs."

In my opinion, spot on. Good choice. If you can spring for Koni's, do so, you won't regret it.
Being an older engine, I have finally come to the realization that I will never achieve push back in the seat performance, even after spending close to 5G on the engine. I have a stage 2 Golf R , same displacement, for that.(385hp) However the handling can be jigged to offer a great experience in the twisties. I have the old IAP red springs, non chopped, and the Koni's. Car sits nicely. I added a larger front sway bar and a rear bar. Went to 15 inch wheels with 205/35? 15 tires.
Not seat back performance but I do notice I will be feeling the side to side while cornering. Fun stuff with the top down.
Naramata, BC Can.
Usually the sunny Okanagan
Nut124
Posts: 748
Joined: Wed Oct 25, 2017 6:39 pm
Your car is a: 1978 124 Spider 1800

Re: cutting springs to lower car

Post by Nut124 »

profcucchi wrote:I gave this a lot of thought, too.

A Fiat and Alfa mechanic told me once you cut springs, you throw off the geometry of the vehicle. and it makes for a stiffer ride.

I decided to hold out until I could get proper lowering springs.
Lowering the car by cutting springs is not a good idea. The cut, shorter springs are too soft to prevent bottoming out in hard bumps.

When lowering the car, the shorter spring must be a lot stiffer in order to keep the suspension from bottoming out with much reduced travel. Cutting springs does not make them stiffer, the opposite.
18Fiatsandcounting
Posts: 3791
Joined: Fri Mar 15, 2019 11:23 pm
Your car is a: 1969 and 1971 124 spiders
Location: San Francisco Bay Area

Re: cutting springs to lower car

Post by 18Fiatsandcounting »

Nut124 wrote:Lowering the car by cutting springs is not a good idea. The cut, shorter springs are too soft to prevent bottoming out in hard bumps.

When lowering the car, the shorter spring must be a lot stiffer in order to keep the suspension from bottoming out with much reduced travel. Cutting springs does not make them stiffer, the opposite.
Good to know, Nut, thanks for that. In the back of my mind, I always had this sense that cutting springs was not a good idea, but I couldn't pinpoint why. Besides, with some of the abrupt driveway entry angles and tall parking lot bump stops around here, the last thing I need is a lower car... :shock:

-Bryan
Nut124
Posts: 748
Joined: Wed Oct 25, 2017 6:39 pm
Your car is a: 1978 124 Spider 1800

Re: cutting springs to lower car

Post by Nut124 »

18Fiatsandcounting wrote:
Nut124 wrote:Lowering the car by cutting springs is not a good idea. The cut, shorter springs are too soft to prevent bottoming out in hard bumps.

When lowering the car, the shorter spring must be a lot stiffer in order to keep the suspension from bottoming out with much reduced travel. Cutting springs does not make them stiffer, the opposite.
Good to know, Nut, thanks for that. In the back of my mind, I always had this sense that cutting springs was not a good idea, but I couldn't pinpoint why. Besides, with some of the abrupt driveway entry angles and tall parking lot bump stops around here, the last thing I need is a lower car... :shock:

-Bryan
I did a little more research on this and will need to admit I was wrong. Cutting a spring shorter does actually increase the spring rate. Whether, in this case, the increased spring rate is enough, or too much, to compensate for the reduced suspension travel or not does not seem easy to calculate.
18Fiatsandcounting
Posts: 3791
Joined: Fri Mar 15, 2019 11:23 pm
Your car is a: 1969 and 1971 124 spiders
Location: San Francisco Bay Area

Re: cutting springs to lower car

Post by 18Fiatsandcounting »

Nut124 wrote:I did a little more research on this and will need to admit I was wrong. Cutting a spring shorter does actually increase the spring rate. Whether, in this case, the increased spring rate is enough, or too much, to compensate for the reduced suspension travel or not does not seem easy to calculate.
Ahhh, Nut, you're a smarter man that I. :D
I'll have to think about this some more, but I guess it makes sense if you think of an extreme: Take an imaginary car spring that is 10 feet long. You could probably pretty easily compress it by hand by one inch. Now cut that same 10 foot long spring so it is only 6 inches long. It would take a lot more force to compress it by one inch, so effectively the spring rate has increased.

In effect, cutting the spring decreases the amount of coils available to flex, so it takes more load to deflect a similar amount, that is, the spring rate has gone up.

However, with cut springs you have to make sure that 1) the ends of the springs still fit as they are supposed to, and 2) lowering the car doesn't cause other effects like stress on your suspension, alignment, ground clearance, etc. For a performance setup, fine. For casual driving on roads with potholes and steep driveways and such, my choice has always been to leave it stock.

Meanwhile, this guy seems to know what he is talking about:
https://www.eatondetroitspring.com/cutt ... culations/

-Bryan
Post Reply