electronic control module

fiat218 · Post by **fiat218** » Fri Sep 23, 2011 5:47 pm

1980 2000
is that the gm made module part?

124JOE · Post by **124JOE** » Fri Sep 23, 2011 6:07 pm

fiat218 · Post by **fiat218** » Fri Sep 23, 2011 9:40 pm

ok thanks

fiat218 · Post by **fiat218** » Mon Sep 26, 2011 9:54 pm

any one ever get a magnetii pickup and it was defective?

124JOE · Post by **124JOE** » Tue Sep 27, 2011 6:05 pm

not me.i had points before i converted to ele ING crain cams fireball3000

fiat218 · Post by **fiat218** » Tue Sep 27, 2011 6:48 pm

well on the 1980,. im having one hell of a time to get spark, so finally i took it to my ace mechanic and he adjusted the timing and the gap between the pick up coil and the dizzy part , that was way off and so he check the new pickup and it did not read no ohms and it was suppose to read 800, so he told me the new one i bought was shot

124JOE · Post by **124JOE** » Tue Sep 27, 2011 6:50 pm

i hate it when that happens

manoa matt · Post by **manoa matt** » Tue Sep 27, 2011 6:55 pm

The magnetic pickups come with a magnet that goes between the pickup and the plate on the distributor. The magnet has a stripe painted on one side. The side of the magnet with the stripe should face down. Check the orientation of the magnet. The air gap between the pickup and stator should be 0.5mm to 0.6mm.

fiat218 · Post by **fiat218** » Tue Sep 27, 2011 6:57 pm

yes i got that right, and i thing he gap that part from the book he has

i notice that on that magnet of the strip . and there was a paper saying wrong way facing up
why is that, north,south pole? correct, and what happns if facing wrong
just wondering

fiat218 · Post by **fiat218** » Tue Sep 27, 2011 7:31 pm

i think he gaped at 4? im not postive, just seems to recall a 0.4mm

124JOE · Post by **124JOE** » Tue Sep 27, 2011 8:46 pm

magenets have N/S and use that as a signal by mesuring the pull when the steel pointer goes bye.
they dont have E/W.if they did i would think they would cancile out

fiat218 · Post by **fiat218** » Tue Sep 27, 2011 10:21 pm

well that what i figured, so if it was on backwards what would happen? i assume nothing

124JOE · Post by **124JOE** » Wed Sep 28, 2011 5:41 am

yes,it only reads the pull in one direction

fiat218 · Post by **fiat218** » Wed Sep 28, 2011 6:24 am

that was kinda what i thought but was not sure, thanks for helping me, i get the new pickup today so i hope this works out

fiat218 · Post by **fiat218** » Thu Sep 29, 2011 6:32 am

new pickup for the 1980 came it and all well, started up, so i pulled it back home , this car been sitting for 6/7 years , so the mechanic told me to just let it idol for a while and change the oil etc and check things out, so far the cooling fan did not come on so i will look into that today

electronic control module

electronic control module

Re: electronic control module

Re: electronic control module

Re: electronic control module

Re: electronic control module

Re: electronic control module

Re: electronic control module

Re: electronic control module

Re: electronic control module

Re: electronic control module

Re: electronic control module

Re: electronic control module

Re: electronic control module

Re: electronic control module

Re: electronic control module