The 1977 Freebee

This is the place to discuss restoration problems, post questions or projects-complete or partial.
Oldschoolbuilder
Posts: 6
Joined: Tue Mar 13, 2018 7:35 pm
Your car is a: 1977 Fiat Spider

The 1977 Freebee

Postby Oldschoolbuilder » Mon Mar 19, 2018 3:43 pm

A friend had this car laying around and when I saw it I was really attracted to the body lines. Long story short he gave me the car. I towed it up to my shop last weekend and played around with it a bit and got it to fire up. Figured now I can do some minor mechanical work on the motor and see if I can get it to stay running and then figure out what direction I want the build to go.

This weekend I got under the car to see what gems might be awaiting me since it sat outside for the better part of a decade. surprisingly there are only a few spots on the drivers side floor that have cancer. But the surprises didn't end there... oh no. The bottom of the fuel tank is pretty much non-existent, I can literally reach up into the tank and touch the sending unit. Guessing I will be replacing that. The rear suspension is pretty much hammered, the panhard rod is bent and kinked, and both trailing arms are bent. Few issues to sort before she makes any sort of maiden voyages.
Image
Image
Image
Last edited by Oldschoolbuilder on Tue Mar 20, 2018 1:34 am, edited 1 time in total.

DRUMMOND
Patron 2018
Patron 2018
Posts: 443
Joined: Thu Oct 20, 2011 11:11 pm
Your car is a: Fiat Spyder 2000 1980 Pininfarina

Re: The 1977 Freebee

Postby DRUMMOND » Mon Mar 19, 2018 10:06 pm

Welcome to your new addiction :D

User avatar
Nanonevol
Patron 2018
Patron 2018
Posts: 828
Joined: Thu Nov 13, 2014 9:17 am
Your car is a: 1977 Fiat 124 Spider
Location: Medway, Massachusetts

Re: The 1977 Freebee

Postby Nanonevol » Tue Mar 20, 2018 9:12 am

Welcome and good job saving another Spider! That smog stuff can go unless you're in Cali.
1977 Fiat Spider
1985 Jaguar XJ6
1967 Triumph Bonneville (hard-tail chopper)
1966 BSA Lightning

Oldschoolbuilder
Posts: 6
Joined: Tue Mar 13, 2018 7:35 pm
Your car is a: 1977 Fiat Spider

Re: The 1977 Freebee

Postby Oldschoolbuilder » Wed May 30, 2018 11:44 pm

New thermostat, water pump, coolant "T", and hoses where picked up and installed. I used a long flexible wire brush through the engine block and as far into the head as I could while running a hose into the block to clean everything out.

Image
Image

Next I tried running the car with a fuel line tucked into a jerry can...with no luck. So I installed an electric fuel pump and found That the fuel line was clogged and broken. Luckily I happened to have one I could rebend to fit, then we had some luck and she fired on her own steam. Then the gent I got the radiator from gave me the number for a guy who had a fuel tank for me... and a new panhard rod. So now she holds petrol and runs on her own, the only thing left is to try and drive her.

Image

I did have to replace the accelerator pump on the carberator, but the car has sat for 25yrs so I think I'm still doing well.
The clutch was stuck on the first drive attempt, but after about 1/8th mile it freed right up and started working like a champ.

Image

A few trial and error minor items but the car runs and drives well. Next I need to go through the fluids in the drive train, I made sure everything was up before driving it but now I want to drain and add fresh. Then some new trailing arms, and finally start figuring out the electrical issues. Nothing in the car works except the ignition and the electric fan is hardwired to a constant on with ignition power

Image
Last edited by Oldschoolbuilder on Thu May 31, 2018 10:13 am, edited 1 time in total.

User avatar
Nanonevol
Patron 2018
Patron 2018
Posts: 828
Joined: Thu Nov 13, 2014 9:17 am
Your car is a: 1977 Fiat 124 Spider
Location: Medway, Massachusetts

Re: The 1977 Freebee

Postby Nanonevol » Thu May 31, 2018 9:45 am

Plan on a new timing belt ASAP and I'll bet you need to replace the "Guibo" - the donut shaped thingie on the driveshaft.
1977 Fiat Spider
1985 Jaguar XJ6
1967 Triumph Bonneville (hard-tail chopper)
1966 BSA Lightning

Oldschoolbuilder
Posts: 6
Joined: Tue Mar 13, 2018 7:35 pm
Your car is a: 1977 Fiat Spider

Re: The 1977 Freebee

Postby Oldschoolbuilder » Thu May 31, 2018 10:20 am

I didn't realize I lost the top half of my post.

The timing belt and tensioner pulley have been replaced as well. The radiator is new also, thanks to a really nice guy from a craigslist add.

Oldschoolbuilder
Posts: 6
Joined: Tue Mar 13, 2018 7:35 pm
Your car is a: 1977 Fiat Spider

Re: The 1977 Freebee

Postby Oldschoolbuilder » Thu May 31, 2018 10:24 am

Nanonevol wrote:Plan on a new timing belt ASAP and I'll bet you need to replace the "Guibo" - the donut shaped thingie on the driveshaft.


Part of why it took me so long to get anything done on the car was waiting on the timing belt and pulley. When I first got it I didn't know it was an interference motor, luckily before I got to far along with it I joined the forums here and found that out. I'll have to look at the "Guibo" I did hear a little bit of noise from under the car on gear changes.-Thank you

User avatar
RRoller123
Patron 2020
Patron 2020
Posts: 8179
Joined: Sun Nov 13, 2011 2:04 pm
Your car is a: 1980 FI SPIDER 2000
Location: SAGAMORE BEACH, MA USA

Re: The 1977 Freebee

Postby RRoller123 » Thu May 31, 2018 1:59 pm

I would replace every fluid in the car, and make sure that you change the gearbox to NAPA GL-1. Chances are that it has lube in it that will attack the brass synchros, put in there by an unknowing PO.
'80 FI Spider 2000
'74 and '79 X1/9 (past)
'75 BMW R75/6
2011 Chevy Malibu (daily driver)
2010 Chevy Silverado 2500HD Ext Cab 4WD/STD BED
2002 Edgewater 175CC 80HP 4-Stroke Yamaha
2003 Jaguar XK8
2003 Jaguar XKR
2021 Jayco 22RB
2019 Bianchi Torino Bicycle


Return to “Restoration Projects”

Who is online

Users browsing this forum: No registered users and 39 guests